|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
(R) D NEW FOR DED 364 N MME E EL5 ECO SE OT R N NS ESIG EL5392A January 22, 2004 FN7194 Data Sheet Triple 600MHz Current Feedback Amplifier with Enable The EL5392A is a triple current feedback amplifier with a very high bandwidth of 600MHz. This makes this amplifier ideal for today's high speed video and monitor applications. With a supply current of just 6mA per amplifier and the ability to run from a single supply voltage from 5V to 10V, the EL5392A is also ideal for hand held, portable or battery powered equipment. The EL5392A also incorporates an enable and disable function to reduce the supply current to 100A typical per amplifier. Allowing the CE pin to float or applying a low logic level will enable the amplifier. For applications where board space is critical, the EL5392A is offered in the 16-pin QSOP package, as well as an industry-standard 16-pin SO (0.150"). The EL5392A operates over the industrial temperature range of -40C to +85C. Features * 600MHz -3dB bandwidth * 6mA supply current (per amplifier) * Single and dual supply operation, from 5V to 10V * Fast enable/disable * Available in 16-pin QSOP package * Single (EL5192) and dual (EL5292) available * High speed, 1GHz product available (EL5191) * Low power, 4mA, 300MHz product available (EL5193, EL5293, and EL5393) Applications * Video amplifiers * Cable drivers * RGB amplifiers * Test equipment * Instrumentation * Current to voltage converters Pinout EL5392 [16-PIN SO (0.150") & QSOP] TOP VIEW Ordering Information PART NUMBER EL5392ACS EL5392ACS-T7 EL5392ACS-T13 EL5392ACU EL5392ACU-T13 PACKAGE 16-Pin SO (0.150") 16-Pin SO (0.150") 16-Pin SO (0.150") 16-Pin QSOP 16-Pin QSOP TAPE & REEL 7" 13" 13" PKG. NO. MDP0027 MDP0027 MDP0027 MDP0040 MDP0040 INA+ 1 CEA 2 VS- 3 CEB 4 INB+ 5 NC 6 CEC 7 INC+ 8 + + + 16 INA15 OUTA 14 VS+ 13 OUTB 12 INB11 NC 10 OUTC 9 INC- 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright (c) Intersil Americas Inc. 2004. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc. All other trademarks mentioned are the property of their respective owners. EL5392A Absolute Maximum Ratings (TA = 25C) Supply Voltage between VS+ and VS- . . . . . . . . . . . . . . . . . . . . . 11V Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 50mA Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 125C Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Pin Voltages. . . . . . . . . . . . . . . . . . . . . . . . .VS- - 0.5V to VS+ +0.5V Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA Electrical Specifications PARAMETER AC PERFORMANCE BW -3dB Bandwidth VS+ = +5V, VS- = -5V, RF = 750 for AV = 1, RF = 375 for AV = 2, RL = 150, TA = 25C unless otherwise specified. DESCRIPTION CONDITIONS MIN TYP MAX UNIT AV = +1 AV = +2 600 300 25 MHz MHz MHz V/s ns dB nV/Hz pA/Hz pA/Hz % BW1 SR tS CS eN iNiN+ dG dP 0.1dB Bandwidth Slew Rate 0.1% Settling Time Channel Separation Input Voltage Noise IN- Input Current Noise IN+ Input Current Noise Differential Gain Error (Note 1) Differential Phase Error (Note 1) AV = +2 AV = +2 VO = -2.5V to +2.5V, AV = +2 VOUT = -2.5V to +2.5V, AV = -1 f = 5MHz 2000 2300 9 60 4.1 20 50 0.015 0.04 DC PERFORMANCE VOS TCVOS ROL Offset Voltage Input Offset Voltage Temperature Coefficient Transimpediance Measured from TMIN to TMAX 200 -10 1 5 400 10 mV V/C k INPUT CHARACTERISTICS CMIR CMRR +IIN -IIN RIN CIN Common Mode Input Range Common Mode Rejection Ratio + Input Current - Input Current Input Resistance Input Capacitance 3 42 -60 -40 3.3 50 3 4 37 0.5 60 40 V dB A A k pF OUTPUT CHARACTERISTICS VO Output Voltage Swing RL = 150 to GND RL = 1k to GND IOUT SUPPLY ISON ISOFF Supply Current - Enabled Supply Current - Disabled No load, VIN = 0V No load, VIN = 0V 5 6 100 7.5 150 mA A Output Current RL = 10 to GND 3.4 3.8 95 3.7 4.0 120 V V mA 2 EL5392A Electrical Specifications PARAMETER PSRR -IPSR ENABLE tEN tDIS IIHCE IILCE VIHCE VILCE NOTE: 1. Standard NTSC test, AC signal amplitude = 286mVP-P, f = 3.58MHz Enable Time Disable Time CE Pin Input High Current CE Pin Input Low Current CE Input High Voltage for Power-down CE Input Low Voltage for Power-down CE = VS+ CE = VSVS+ - 1 VS+ - 3 40 600 0.8 0 6 -0.1 ns ns A A V V VS+ = +5V, VS- = -5V, RF = 750 for AV = 1, RF = 375 for AV = 2, RL = 150, TA = 25C unless otherwise specified. (Continued) DESCRIPTION Power Supply Rejection Ratio - Input Current Power Supply Rejection CONDITIONS DC, VS = 4.75V to 5.25V DC, VS = 4.75V to 5.25V MIN 55 -2 TYP 75 2 MAX UNIT dB A/V 3 EL5392A Typical Performance Curves Non-Inverting Frequency Response (Gain) 6 AV=1 Normalized Magnitude (dB) 2 AV=2 0 AV=1 AV=2 Phase () -2 AV=5 -6 AV=10 -10 RF=750 RL=150 -14 1M 10M 100M Frequency (Hz) 1G -360 1M -270 RF=750 RL=150 10M 100M Frequency (Hz) 1G -90 AV=5 AV=10 90 Non-Inverting Frequency Response (Phase) -180 Inverting Frequency Response (Gain) 6 AV=-1 AV=-2 90 Inverting Frequency Response (Phase) Normalized Magnitude (dB) 2 0 AV=-1 Phase () -2 AV=-5 -6 -90 AV=-2 AV=-5 -180 -10 RF=375 RL=150 -14 1M 10M 100M Frequency (Hz) 1G -270 RF=375 RL=150 -360 1M 10M 100M Frequency (Hz) 1G Frequency Response for Various CIN10 2pF added Normalized Magnitude (dB) 6 1pF added 2 Normalized Magnitude (dB) 2 6 Frequency Response for Various RL RL=150 RL=100 -2 RL=500 -2 0pF added -6 -6 AV=2 RF=375 RL=150 10M 100M 1G -10 AV=2 RF=375 -14 1M 10M 100M 1G -10 1M Frequency (Hz) Frequency (Hz) 4 EL5392A Typical Performance Curves (Continued) Frequency Response for Various CL 14 AV=2 RF=375 RL=150 6 Frequency Response for Various RF 250 Normalized Magnitude (dB) 12pF added 2 375 Normalized Magnitude (dB) 10 475 -2 620 750 6 8pF added 2 -6 -2 0pF added -10 AV=2 RG=RF RL=150 10M 100M Frequency (Hz) 1G -6 1M 10M 100M 1G -14 1M Frequency (Hz) Group Delay vs Frequency 3.5 3 Group Delay (ns) 2.5 2 1.5 1 0.5 0 1M AV=1 RF=750 AV=2 RF=375 6 Frequency Response for Various Common-Mode Input Voltages VCM=3V Normalized Magnitude (dB) 2 VCM=0V -2 VCM=-3V -6 -10 AV=2 RF=375 RL=150 10M 100M 1G 10M 100M 1G -14 1M Frequency (Hz) Frequency (Hz) Transimpedance (ROL) vs Frequency 10M 0 1M Magnitude () Phase PSRR/CMRR (dB) -90 Phase () 100k -180 10k Gain 1k -360 100 1k 10k 100k 1M 10M 100M 1G -270 0 20 PSRR and CMRR vs Frequency PSRR+ -20 PSRR-40 -60 CMRR -80 10k 100k 1M 10M 100M 1G Frequency (Hz) Frequency (Hz) 5 EL5392A Typical Performance Curves (Continued) -3dB Bandwidth vs Supply Voltage for Non-Inverting Gains 800 RF=750 RL=150 -3dB Bandwidth (MHz) 600 AV=1 -3dB Bandwidth (MHz) 350 300 250 -3dB Bandwidth vs Supply Voltage for Inverting Gains AV=-1 AV=-2 200 AV=-5 150 100 50 0 RF=375 RL=150 5 6 7 8 9 10 400 AV=2 200 AV=5 AV=10 0 5 6 7 8 9 10 Total Supply Voltage (V) Total Supply Voltage (V) Peaking vs Supply Voltage for Non-Inverting Gains 4 RF=750 RL=150 3 Peaking (dB) AV=1 Peaking (dB) 3 4 Peaking vs Supply Voltage for Inverting Gains AV=-1 RF=375 RL=150 2 2 AV=-2 1 AV=2 1 AV=10 0 AV=-5 0 5 6 7 8 9 10 Total Supply Voltage (V) 5 6 7 8 9 10 Total Supply Voltage (V) -3dB Bandwidth vs Temperature for Non-Inverting Gains 1400 1200 -3dB Bandwidth (MHz) 1000 800 600 400 AV=2 200 0 -40 AV=5 AV=10 AV=1 RF=750 RL=150 400 -3dB Bandwidth (MHz) 500 -3dB Bandwidth vs Temperature for Inverting Gains AV=-1 RF=375 RL=150 300 AV=-2 200 AV=-5 100 10 60 110 160 0 -40 10 60 110 160 Ambient Temperature (C) Ambient Temperature (C) 6 EL5392A Typical Performance Curves Peaking vs Temperature 2 RL=150 Voltage Noise (nV/Hz) Current Noise (pA/Hz) 1.5 Peaking (dB) AV=1 1k (Continued) Voltage and Current Noise vs Frequency 100 in10 in+ 1 AV=-1 0.5 AV=-2 en 0 AV=2 -0.5 -50 -50 0 50 100 1 100 1k 10k 100k 1M 10M Ambient Temperature (C) Frequency (Hz) Closed Loop Output Impedance vs Frequency 100 10 Supply Current vs Supply Voltage 10 Output Impedance () Supply Current (mA) 8 1 6 0.1 4 0.01 2 0.001 100 1k 10k 100k 1M 10M 100M 1G Frequency (Hz) 0 0 2 4 6 8 10 12 Supply Voltage (V) 2nd and 3rd Harmonic Distortion vs Frequency -20 -30 Harmonic Distortion (dBc) -40 -50 -60 -70 -80 -90 -100 1 10 Frequency (MHz) 100 2nd Order Distortion 3rd Order Distortion Input Power Intercept (dBm) AV=+2 VOUT=2VP-P RL=100 30 25 20 15 10 5 0 -5 -10 Two-Tone 3rd Order Input Referred Intermodulation Intercept (IIP3) AV=+2 RL=150 AV=+2 RL=100 100 Frequency (MHz) 200 -15 10 7 EL5392A Typical Performance Curves (Continued) Differential Gain/Phase vs DC Input Voltage at 3.58MHz 0.03 0.02 0.01 dG (%) or dP () dG (%) or dP () 0 -0.01 -0.02 -0.03 -0.04 -0.05 -1 dG AV=2 RF=RG=375 RL=150 0.03 0.02 dP 0.01 0 -0.01 -0.02 -0.03 -0.04 -0.05 -0.5 0 DC Input Voltage 0.5 1 Differential Gain/Phase vs DC Input Voltage at 3.58MHz AV=1 RF=750 RL=500 dP dG -0.06 -1 -0.5 0 DC Input Voltage 0.5 1 Output Voltage Swing vs Frequency THD<1% 9 8 Output Voltage Swing (VPP) 7 6 5 4 3 2 1 AV=2 0 1 10 Frequency (MHz) 100 0 RL=150 RL=500 Output Voltage Swing (VPP) 8 10 Output Voltage Swing vs Frequency THD<0.1% RL=500 RL=150 6 4 2 AV=2 1 10 Frequency (MHz) 100 Small Signal Step Response Large Signal Step Response VS=5V RL=150 AV=2 RF=RG=375 VS=5V RL=150 AV=2 RF=RG=375 200mV/div 1V/div 10ns/div 10ns/div 8 EL5392A Typical Performance Curves (Continued) Settling Time vs Settling Accuracy 25 AV=2 RF=RG=375 RL=150 VSTEP=5VP-P output RoI (k) 500 Transimpedance (RoI) vs Temperature 20 Settling Time (ns) 450 15 400 10 350 5 0 0.01 0.1 Settling Accuracy (%) 1 300 -40 10 60 Die Temperature (C) 110 160 PSRR and CMRR vs Temperature 90 80 70 60 CMRR 50 40 30 20 10 -40 ICMR/IPSR (A/V) PSRR/CMRR (dB) PSRR 2.5 2 1.5 1 0.5 0 -0.5 ICMR and IPSR vs Temperature ICMR+ IPSR ICMR- 10 60 Die Temperature (C) 110 160 -1 -40 10 60 Die Temperature (C) 110 160 Offset Voltage vs Temperature 3 60 40 2 Input Current (A) 20 Input Current vs Temperature VOS (mV) 1 IB0 -20 -40 -60 IB+ 0 -1 -2 -40 10 60 Die Temperature (C) 110 160 -80 -40 10 60 Temperature (C) 110 160 9 EL5392A Typical Performance Curves (Continued) Positive Input Resistance vs Temperature 50 45 40 35 RIN+ (k) 30 25 20 15 10 5 0 -40 10 60 Temperature (C) 110 160 1 Supply Current (mA) 6 5 4 3 2 8 7 Supply Current vs Temperature 0 -40 10 60 Temperature (C) 110 160 Positive Output Swing vs Temperature for Various Loads 4.2 4.1 1k 4 VOUT (V) 3.9 3.8 3.7 3.6 3.5 -40 150 VOUT (V) -3.7 -3.8 -3.9 -4 -4.1 -3.5 -3.6 Negative Output Swing vs Temperature for Various Loads 150 1k 10 50 Temperature (C) 110 160 -4.2 -40 10 60 Temperature (C) 110 160 Output Current vs Temperature 135 4600 4400 130 IOUT (mA) Sink 4200 Slew Rate (V/S) 4000 3800 3600 3400 3200 115 -40 Slew Rate vs Temperature AV=2 RF=RG=375 RL=150 125 Source 120 10 60 Die Temperature (C) 110 160 3000 -40 10 60 Die Temperature (C) 110 160 10 EL5392A Typical Performance Curves (Continued) Package Power Dissipation vs Ambient Temperature JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board 1 0.9 -20 Power Dissipation (W) 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 -100 100k 0 1M 10M Frequency (Hz) 100M 400M 0 25 50 75 85 100 125 150 Ambient Temperature (C) 15 Channel-to-Channel Isolation vs Frequency 0 909mW 11 0 SO 16 Gain (dB) -40 (0 .1 C 50 /W ") QS OP 16 8 C/ W 633mW -60 -80 Enable Response Disable Response 500mV/div 500mV/div 5V/div 5V/div 20ns/div 400ns/div 11 EL5392A Pin Descriptions 16-PIN SO (0.150") 1 16-PIN QSOP 1 PIN NAME INA+ FUNCTION Non-inverting input, channel A EQUIVALENT CIRCUIT VS+ IN+ IN- VSCircuit 1 2 2 CEA Chip enable, channel A VS+ CE VSCircuit 2 3 4 5 6, 11 7 8 9 10 3 4 5 6, 11 7 8 9 10 VSCEB INB+ NC CEC INC+ INCOUTC Negative supply Chip enable, channel B Non-inverting input, channel B Not connected Chip enable, channel C Non-inverting input, channel C Inverting input, channel C Output, channel C (See circuit 2) (See circuit 1) (See circuit 1) VS+ (See circuit 2) (See circuit 1) OUT VSCircuit 3 12 13 14 15 16 12 13 14 15 16 INBOUTB VS+ OUTA INA- Inverting input, channel B Output, channel B Positive supply Output, channel A Inverting input, channel A (See circuit 1) (See circuit 3) (See circuit 3) (See circuit 1) Applications Information Product Description The EL5392A is a current-feedback operational amplifier that offers a wide -3dB bandwidth of 600MHz and a low supply current of 6mA per amplifier. The EL5392A works with supply voltages ranging from a single 5V to 10V and they are also capable of swinging to within 1V of either supply on the output. Because of their current-feedback topology, the EL5392A does not have the normal gainbandwidth product associated with voltage-feedback operational amplifiers. Instead, its -3dB bandwidth to remain 12 relatively constant as closed-loop gain is increased. This combination of high bandwidth and low power, together with aggressive pricing make the EL5392A the ideal choice for many low-power/high-bandwidth applications such as portable, handheld, or battery-powered equipment. For varying bandwidth needs, consider the EL5191 with 1GHz on a 9mA supply current or the EL5193 with 300MHz on a 4mA supply current. Versions include single, dual, and triple amp packages with 5-pin SOT23, 16-pin QSOP, and 8pin or 16-pin SO (0.150") outlines. EL5392A Power Supply Bypassing and Printed Circuit Board Layout As with any high frequency device, good printed circuit board layout is necessary for optimum performance. Low impedance ground plane construction is essential. Surface mount components are recommended, but if leaded components are used, lead lengths should be as short as possible. The power supply pins must be well bypassed to reduce the risk of oscillation. The combination of a 4.7F tantalum capacitor in parallel with a 0.01F capacitor has been shown to work well when placed at each supply pin. For good AC performance, parasitic capacitance should be kept to a minimum, especially at the inverting input. (See the Capacitance at the Inverting Input section) Even when ground plane construction is used, it should be removed from the area near the inverting input to minimize any stray capacitance at that node. Carbon or Metal-Film resistors are acceptable with the Metal-Film resistors giving slightly less peaking and bandwidth because of additional series inductance. Use of sockets, particularly for the SO (0.150") package, should be avoided if possible. Sockets add parasitic inductance and capacitance which will result in additional peaking and overshoot. not recommended around the inverting input pin of the amplifier. Feedback Resistor Values The EL5392A has been designed and specified at a gain of +2 with RF approximately 375. This value of feedback resistor gives 300MHz of -3dB bandwidth at AV=2 with 2dB of peaking. With AV=-2, an RF of 375 gives 275MHz of bandwidth with 1dB of peaking. Since the EL5392A is a current-feedback amplifier, it is also possible to change the value of RF to get more bandwidth. As seen in the curve of Frequency Response for Various RF and RG, bandwidth and peaking can be easily modified by varying the value of the feedback resistor. Because the EL5392A is a current-feedback amplifier, its gain-bandwidth product is not a constant for different closedloop gains. This feature actually allows the EL5392A to maintain about the same -3dB bandwidth. As gain is increased, bandwidth decreases slightly while stability increases. Since the loop stability is improving with higher closed-loop gains, it becomes possible to reduce the value of RF below the specified 375 and still retain stability, resulting in only a slight loss of bandwidth with increased closed-loop gain. Disable/Power-Down The EL5392A amplifier can be disabled placing its output in a high impedance state. When disabled, the amplifier supply current is reduced to < 450A. The EL5392A is disabled when its CE pin is pulled up to within 1V of the positive supply. Similarly, the amplifier is enabled by floating or pulling its CE pin to at least 3V below the positive supply. For 5V supply, this means that an EL5392A amplifier will be enabled when CE is 2V or less, and disabled when CE is above 4V. Although the logic levels are not standard TTL, this choice of logic voltages allows the EL5392A to be enabled by tying CE to ground, even in 5V single supply applications. The CE pin can be driven from CMOS outputs. Supply Voltage Range and Single-Supply Operation The EL5392A has been designed to operate with supply voltages having a span of greater than 5V and less than 10V. In practical terms, this means that the EL5392A will operate on dual supplies ranging from 2.5V to 5V. With singlesupply, the EL5392A will operate from 5V to 10V. As supply voltages continue to decrease, it becomes necessary to provide input and output voltage ranges that can get as close as possible to the supply voltages. The EL5392A has an input range which extends to within 2V of either supply. So, for example, on 5V supplies, the EL5392A has an input range which spans 3V. The output range of the EL5392A is also quite large, extending to within 1V of the supply rail. On a 5V supply, the output is therefore capable of swinging from -4V to +4V. Single-supply output range is larger because of the increased negative swing due to the external pull-down resistor to ground. Capacitance at the Inverting Input Any manufacturer's high-speed voltage- or current-feedback amplifier can be affected by stray capacitance at the inverting input. For inverting gains, this parasitic capacitance has little effect because the inverting input is a virtual ground, but for non-inverting gains, this capacitance (in conjunction with the feedback and gain resistors) creates a pole in the feedback path of the amplifier. This pole, if low enough in frequency, has the same destabilizing effect as a zero in the forward open-loop response. The use of largevalue feedback and gain resistors exacerbates the problem by further lowering the pole frequency (increasing the possibility of oscillation.) The EL5392A has been optimized with a 375 feedback resistor. With the high bandwidth of these amplifiers, these resistor values might cause stability problems when combined with parasitic capacitance, thus ground plane is Video Performance For good video performance, an amplifier is required to maintain the same output impedance and the same frequency response as DC levels are changed at the output. This is especially difficult when driving a standard video load of 150, because of the change in output current with DC level. Previously, good differential gain could only be achieved by running high idle currents through the output transistors (to reduce variations in output impedance.) These currents were typically comparable to the entire 6mA supply current of each EL5392A amplifier. Special circuitry has been incorporated in the EL5392A to reduce the 13 EL5392A variation of output impedance with current output. This results in dG and dP specifications of 0.015% and 0.04, while driving 150 at a gain of 2. Video performance has also been measured with a 500 load at a gain of +1. Under these conditions, the EL5392A has dG and dP specifications of 0.03% and 0.05, respectively. modified for the EL5392A to remain in the safe operating area. These parameters are calculated as follows: T JMAX = T MAX + ( JA x n x PD MAX ) where: TMAX = Maximum ambient temperature JA = Thermal resistance of the package n = Number of amplifiers in the package PDMAX = Maximum power dissipation of each amplifier in the package PDMAX for each amplifier can be calculated as follows: V OUTMAX PD MAX = ( 2 x V S x I SMAX ) + ( V S - V OUTMAX ) x --------------------------R L Output Drive Capability In spite of its low 6mA of supply current, the EL5392A is capable of providing a minimum of 95mA of output current. With a minimum of 95mA of output drive, the EL5392A is capable of driving 50 loads to both rails, making it an excellent choice for driving isolation transformers in telecommunications applications. Driving Cables and Capacitive Loads When used as a cable driver, double termination is always recommended for reflection-free performance. For those applications, the back-termination series resistor will decouple the EL5392A from the cable and allow extensive capacitive drive. However, other applications may have high capacitive loads without a back-termination resistor. In these applications, a small series resistor (usually between 5 and 50) can be placed in series with the output to eliminate most peaking. The gain resistor (RG) can then be chosen to make up for any gain loss which may be created by this additional resistor at the output. In many cases it is also possible to simply increase the value of the feedback resistor (RF) to reduce the peaking. where: VS = Supply voltage ISMAX = Maximum supply current of 1A VOUTMAX = Maximum output voltage (required) RL = Load resistance Current Limiting The EL5392A has no internal current-limiting circuitry. If the output is shorted, it is possible to exceed the Absolute Maximum Rating for output current or power dissipation, potentially resulting in the destruction of the device. Power Dissipation With the high output drive capability of the EL5392A, it is possible to exceed the 125C Absolute Maximum junction temperature under certain very high load current conditions. Generally speaking when RL falls below about 25, it is important to calculate the maximum junction temperature (TJMAX) for the application to determine if power supply voltages, load conditions, or package type need to be All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 14 |
Price & Availability of EL5392ACS |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |